DS3000PE high line: 3000 w low line: 1350 w distributed power bulk front-end single ouptut standard total output power: 3000 w continuous 208 vac to 264 vac, 3000 w 1 90 vac to 140 vac, 1350 w special features ? 3000 w output power ? high power and narrow form factor ? 6 units can ft in a 19 inch for a total of 16.2 kw ? high density design: 24 w/in 3 ? active power factor correction ? en61000-3-2 harmonic compliance ? inrush current control ? 80plus platinum effciency ? n+1 or n+n redundant ? hot-pluggable ? active current sharing ? full digital control ? pmbus compliant ? accurate input power reporting ? compatible with artesyns universal pmbus gui ? two-year warranty compliance ? conducted/radiated emi en55022 class a limits + 6 db margin ? rohs safety ? ul/cul ? demko+ cb report en60950 ? bsmi ? ce mark ? china cqc electrical specifcations input input voltage range 90-140 vac, 1350 w 208 to 264 vac 1 , 3000 w frequency 47 hz to 63 hz effciency 94.0% peak max input current 17.5 arms inrush current 55 apk conducted emi class a radiated emi class a power factor >0.97, typical ithd 10% leakage current 0.58 ma hold-up time 11 ms data sheet ordering information DS3000PE-3 standard airfow DS3000PE-3-001 reverse airfow 1 2700 w output rating at 180 vac power
electrical specifcations output main dc output min nom max nominal setting -0.30% 12 0.30% total output regulation range 11.4 v 12.6 v dynamic load regulation range 11.4 v 12.6 v output ripple 120 mvp-p output current 2 a 4 250 a 5 current sharing within +/-13.8 a of each other capacitive loading 1,000 f 15,000 f start-up from ac to output 2100 ms output rise time 2 ms 60 ms standby dc output nominal setting -1% 12.0 v 1% total output regulation range 11.4 v 12.6 v dynamic load regulation range 11.4 v 12.6 v output ripple 120 mvp-p output current 0.5 a 4.5 a current sharing n/a capacitive loading 47 f 560 f start-up from ac to output 1700 ms output rise time 2 ms 60 ms protections main output overcurrent protection 2 104% 120% overvoltage protection 1 13.5 v 15.0 v undervoltage protection 10.5 v 11.0 v overtemperature protection yes fan fault protection yes standby output overcurrent protection 4 110% 150% overvoltage protection 3 13.5 v 15.0 v undervoltage protection 9.6 v 11.0 v 1 latch mode 2 autorecovery if the overcurrent is less than 104% and last only for <500 ms. 3 standby protection is auto-recovery 4 minimum current for transient load response testing only. unit is designed to operate and be wtihin regulation range at zero load. 5 revere airflow model derates to 231.5 a DS3000PE data sheet
control and status signals input signals pson active low signal which enables/disables the main output. pulling this signal low will turn-on the main output. recommended pull-up resistor to 12 vsb is 8.2 k with a 3.0 k pull-down to ground. a 100 pf decoupling capacitor is also recommended. min max v il input logic level low 0.8 v v ih input logic level high 2.0 v 5.0 v i source current that may be sourced by this pin 2 ma i sink current that may be sunk by this pin at low state 0.5 ma pskil first break/last mate active low signal which enables/disables the main output. this signal will have to be pulled to ground at the system side with a 220 ohm resistor. a 100 pf decoupling capacitor is also recommended. min max v il input logic level low 0.8 v v ih input logic level high 2.0 v 5.0 v i source current that may be sourced by this pin 2 ma i sink current that may be sunk by this pin at low state 0.5 ma a0, a1, a2 addressing pins of the power supply for i 2 c communications. refer to the addressing tables below. min max internal pull-ups to 3.3v. it is recommended for the system to have pull-ups and decoupling on the address lines for better noise immunity. r = 22 k ohm c = 47 pf v il input logic level low 0.8 v v ih input logic level high 2.0 v 5.0 v i source current that may be sourced by this pin 4 ma i sink current that may be sunk by this pin 4 ma output signals acok signal used to indicate the presence of ac input to the power supply. a logic level high will indicate that the ac input to the power supply is within the operating range while a logic level low will indicate that ac has been lost. this is an open collector/drain output. this pin is pulled high by a 1.0 k ohm resistor connected to 3.3 v inside the power supply. it is recommended that this pin be connected to a 100 pf decoupling capacitor and pulled down by a 100 k ohm resistor. min max v il output logic level low 0.6 v v ih output logic level high 2.0 v 5.0 v i source current that may be sourced by this pin 3.3 ma i sink current that may be sunk by this pin at low state 0.7 ma DS3000PE data sheet
control and status signals pwr_good / pwok signal used to indicate that main output voltage is within regulation range. the pwr_good signal will be driven high when the output voltage is valid and will be driven low when the output falls below the under-voltage threshold. this signal also gives an advance warning when there is an impending power loss due to loss of ac input or system shutdown request. more details in the timing section. this is an open collector/drain output. this pin is pulled high by a 1.0 k ohm resistor connected to 3.3 v inside the power supply. it is recommended that this pin be connected to a 100 pf decoupling capacitor and pulled down by a 10 k ohm resistor. min max v il output logic level low 0.8 v v ih output logic level high 2.0 v 5.0 v i source current that may be sourced by this pin 3.3 ma i sink current that may be sunk by this pin at low state 0.7 ma ps_present signal used to indicate to the system that a power supply is inserted in the power bay. recommended pull-up resistor to 12 vsb is 8.2 k with a 3.0 k pull-down to ground. a 100 pf decoupling capacitor is also recommended. ps_interrupt active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. this event can be triggered by faults such as ovp, ocp, otp, and fan fault. this signal can be cleared by a clear_fault command. recommended pull-up resistor to 12 vsb is 8.2 k with a 3.0 k pull-down to ground. a 100 pf decoupling capacitor is also recommended. min max v il output logic level low 0.8 v v ih output logic level high 2.0 v 5.0 v i source current that may be sourced by this pin 4 ma i sink current that may be sunk by this pin at low state 4 ma bus signals ishare bus signal used by the power supply for active current sharing. all power supplies confgured in the system for n+n sharing will refer to this bus voltage inorder to load share. voltage range the range of this signal for active sharing will be up to 8.0 v, which corresponds to the maximum output current. min max i share voltage input logic level low 7.75 8.25 voltage at 50% load, stand-alone unit 3.85 4.15 voltage at 0% load, stand-alone unit 0 0.3 i source current that may be sourced by this pin 160 ma scl, sda clock, data and addressing signals defned as per i 2 c requirements. the maximum system side resistor pull-up and decoupling capacitance min max v l logic level low 0.8 v v h logic level high 2.0 v 5.0 v note: all signal noise levels are below 400 mvpk-pk from 0 - 100 mhz. i 2 c addressing table fru addressing a2 a1 a0 address high low low 0 x a9 high low high 0 x ab high high low 0 x ad high high high 0 x af* * default address when ao and a1 are open pmbus addressing address 0 x b8 0 x ba 0 x bc 0 x be DS3000PE data sheet
firmware reporting and monitoring accuracy range output loading 5 to 20% 20 to 50% 50 to 100% input voltage 5% input current 0.55 a fxed error 4% input power 10 w at < 100 w input 5% output voltage 2% output current 2.5 a fxed error 2% temperature 5 degc on the operating range e in 15% from 10% to 20% load 5% fan speed 250 rpm pmbus yes remote on/off yes electrical specifcations led indicators ac good led dc good led fault led color green green amber no ac input to psu off off off ac present, stby on, main output off on off off main output on on on off power supply failure (ovp, otp, fan fault) off off blinking timing specifcations description min max unit t sb_on delay from ac being applied to standby output being within regulation 500 2000 ms t sb_vout delay from standby output to main output voltage being within regulation 1200 ms t sb_acok delay from standby output to acok assertion 40 ms t ac_on_delay delay from ac being applied to main output being within regulation 2200 ms t pwok_on delay from output voltages within regulation limits to pwok asserted 100 1200 ms t acok_delay delay from loss of ac to assertion of acok 250 ms t pwok_hold-up delay from loss of ac to deassertion of pwok 10 ms t vout_hold-up delay from loss of ac to main output falling out of regulation 11 ms t sb_hold-up delay from loss of ac to standby output being within regulation 150 ms t pwr_good_off delay from deassertion of pwok to output falling out of regulation 1 ms t pson_on_delay delay from pson assertion to output being within regulation 350 ms DS3000PE data sheet
timing diagram pson vout_main pwok acok vout_stby ac input t sb_on t ac_on_delay t sb_vout t pson_on_delay t sb_hold-up t pwok_hold-up t vout_hold-up t pwok_o? t acok_delay t pwok_on t sb_acok environmental specifcations operating temperature full power from 0 to 40 c, derate output power by 2.5% per c from 40 c to 50 c operating altitude up to 10,000 feet operating relative humidity 20% to 80% non-condensing non-operating temperature -40 to +85 c non-operating relative humidity 10% to 95% non-condensing non-operating altitude up to 30,000 feet vibration and shock standard operating/non-operating random vibration/shock rohs compliance yes mtbf 400,000 hours operating life minimum of 5 years reliability all electronic component derating analysis and capacitor life calculation is done at 25 degc ambient, maximum rated load, nominal input line voltage. DS3000PE data sheet
mechanical outline DS3000PE data sheet
DS3000PE 30jul2015 connector defnitions output connector part number 75555-104 mating connector part number 75541-104revb1 or any other molex recommended part pin signal name amps per pin 1 pb1 return 150 pb2 return 150 pb3 12 v 150 pb4 12 v 150 a1 pwr good n/a a2 pskill n/a a3 present n/a b1 return n/a b2 ishare n/a b3 return n/a c1 ps_interrupt n/a c2 return n/a c3 acok n/a d1 return n/a d2 pson n/a d3 reserved n/a e1 sda n/a e2 scl n/a e3 a0 n/a f1 reserved n/a f2 a1 n/a f3 a2 n/a g1 reserved n/a g2 reserved n/a g3 reserved n/a h1 12 vsb 2 h2 12 vsb 2 h3 12 vsb 2 DS3000PE data sheet for more information: www.artesyn.com/power for support: productsupport.ep@artesyn.com www.artesyn.com worldwide offices americas 2900 s.diablo way tempe, az 85282 usa +1 888 412 7832 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom +44 (0) 1384 842 211 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong +852 2176 3333 while every precaution has been taken to ensure accuracy and completeness in this literature, artesyn embedded technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. artesyn embedded technologies, artesyn and the artesyn embedded technologies logo are trademarks and service marks of artesyn embedded technologies, inc. all other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. ? 2015 artesyn embedded technologies, inc.
|
